The (p) prolgram
Jan 1, 2013 13:02:26 #
Nicon D90 when i put my camera into this program and try to mover the f numbers and shutter it does not move.IT does not matter what why i turn the commamd dial.a few times a x popt up .help please . manual does not give much help
Jan 1, 2013 14:15:43 #
"Ni"k"on"
Of course it wont it is in PROGRAM the camera decides.
Chose Manual, Time, or AP
Instruction manual
Of course it wont it is in PROGRAM the camera decides.
Chose Manual, Time, or AP
Instruction manual
Jan 1, 2013 14:22:06 #
tamurman wrote:
Nicon D90 when i put my camera into this program and try to mover the f numbers and shutter it does not move.IT does not matter what why i turn the commamd dial.a few times a x popt up .help please . manual does not give much help
The Information is in your NKON manual !!
Jan 1, 2013 16:18:54 #
when u put it in p program you should be able to to change the number with the command dial up and down it is not leting me do that . i HAVE read the manual it does not help much or i would not be asking u guys but then again that is what i thought uhh was all about .?????
Jan 1, 2013 16:21:11 #
i have read the manual it does not explain what i am asking :-D a manual only tells you how a program should work how many times have you followed the manual and you still could not get the thing to work!!!!????if you had took the time to read the post you would have seen i said i had read the manual
Jan 1, 2013 16:28:40 #
Pepper
Loc: Planet Earth Country USA
Are you asking the camera to go beyond the capability of the lens? Are you trying to go beyond the limits of the cameras ability to properly expose the shot?
Jan 1, 2013 17:39:20 #
NIKON D 90 p prolgram in this mode the camera chooses the f/stop and shutter speed .IF you want different aperture and shutter speeds rotate the rear command dial whitch selects altermate f.stops and shutter speeds whitch gives you the same exposure .so you can change thing in the program!! you to can deside the shutter speed and f.stops in this mode not just the camera as you said JR1 ALL this crap cause people will not take the time to read this right so so sad all i wanted was some advice when i turn the command dial nothing moves
Jan 1, 2013 17:41:16 #
Jan 1, 2013 17:42:33 #
JR1 wrote:
ii"Ni"k"on"
Of course it wont it is in PROGRAM the camera decides.
Chose Manual, Time, or AP
Instruction manual
Of course it wont it is in PROGRAM the camera decides.
Chose Manual, Time, or AP
Instruction manual
Jan 1, 2013 18:37:47 #
FilmFanatic
Loc: Waikato, New Zealand
Up and down? The command dial doesn't go up and down. You are using the wrong dial I think, the command dial is the one at the back at the top that goes left and right, NOT the 4 way controller thing
Jan 1, 2013 18:44:23 #
tamurman wrote:
no i am only trying to get the numbers to move that is all
With the setting at "P" you should be able to change the f-stop (shutter speed will automatically change in relation to f-stop)
Use the command dial ("wheel") on the top back side(right)
Jan 1, 2013 20:20:19 #
yes i am using the command dial do you think i am daft i read the manual and dont know were the command dial is if you dont have a good answer please dont comment on my posts i know what all the buttons and dials on the camera are for are you drunk!!!!???the command dial goes from left to right this is to film fanatic
Jan 1, 2013 20:23:47 #
FilmFanatic
Loc: Waikato, New Zealand
tamurman wrote:
yes i am using the command dial do you think i am daft i read the manual and dont know were the command dial is if you dont have a good answer please dont comment on my posts i know what all the buttons and dials on the camera are for are you drunk!!!!???
Excuse me? You said "UP AND DOWN". The command dial does not go up and down. Perhaps you were drunk when you wrote that
Jan 1, 2013 20:25:14 #
tamurman wrote:
yes i am using the command dial do you think i am daft i read the manual and dont know were the command dial is if you dont have a good answer please dont comment on my posts i know what all the buttons and dials on the camera are for are you drunk!!!!???
Only trying to be helpful!!!!!!!!!!! No need to get all flippy
Jan 1, 2013 20:28:39 #
tamurman wrote:
yes i am using the command dial do you think i am daft i read the manual and dont know were the command dial is if you dont have a good answer please dont comment on my posts i know what all the buttons and dials on the camera are for are you drunk!!!!???
I don't use P mode, never have, never will, but may suggest taking to youtube or google for your answers. You seem a little angry at the moment and might need a little breather.
If you want to reply, then register here. Registration is free and your account is created instantly, so you can post right away.