Jeffcs wrote:
I would thing the micro cards could not be as fast as standard add to that another set of contacts personally I wouldn’t use them
The
same IC (memory chip) goes into both cards, the adapter is less than an inch of "wires",
Why (and how) would the micros be slower???
The contacts are gold plated, they don't tarnish.
(Unless maybe one gets their lunch on the contacts, but then the contact springs "wipe" (under a bit of pressure) the card contacts (one can see the wear on the card contacts. They should be kept relatively clean though.)
The extra set of contacts are not a real problem.
Those that don't understand things are fearful of them.
User ID wrote:
I have video project idea that will most likely involve more frequent removal and exchange of the memory cards. Therefor I will definitely go with micro SD cards. I can extract micros directly from the adapter without ejecting the adapter. This eliminates beating up the card latching and ejection mechanism.
Hawgsters are rather fearful of adapters for both cards and lenses. Makes for great multi page arguments and lengthy pontification in the Great UHH Sacred Tradition.
This is the strongest reasoning yet for micros... avoid wear and tear on the camera mechanisms.
Jeffcs wrote:
I would thing the micro cards could not be as fast as standard add to that another set of contacts personally I wouldn’t use them
ROTFLMFAO, puuuuure UHH .....
kmielen wrote:
This is the strongest reasoning yet for micros... avoid wear and tear on the camera mechanisms.
I am not sure if I use the microSD with an adapter for my camera I can pull the microSD card out without removing the adapter from the camera or not.
BebuLamar wrote:
I am not sure if I use the microSD with an adapter for my camera I can pull the microSD card out without removing the adapter from the camera or not.
Biddy card, fat fingers (no nails), I have an adapter for each micro and just remove the whole thing.
Not like I'm doing it 10 times a day.
Longshadow wrote:
Biddy card, fat fingers (no nails), I have an adapter for each micro and just remove the whole thing.
Not like I'm doing it 10 times a day.
My post is in response to the one post that said he use the microSD to prevent wear on his camera so I take it he meant he doesn't remove the adapter when removing the microSD card for downloading the images.
Why use two items when one will do the job?
BebuLamar wrote:
My post is in response to the one post that said he use the microSD to prevent wear on his camera so I take it he meant he doesn't remove the adapter when removing the microSD card for downloading the images.
Correct.
My post was in response to leaving the adapter in the camera and removing the micro from the adapter.
BebuLamar wrote:
I am not sure if I use the microSD with an adapter for my camera I can pull the microSD card out without removing the adapter from the camera or not.
Needs finger nails, or grippy tweazers. There *might be* certain cameras where its just too awkward to be worth it.
For my project, if a camera happens to be too awkward then I would just use one thaz more convenient for the purpose. My mini laptop PC has one card slot and its for mini.
Dan S wrote:
I was just wondering which would be better. sd cards or micro sd cards in an adapter?
I wired a radio station in my early 20s. The chief engineer taught me a very valuable lesson: When confronted with a choice of more or fewer connections in any circuit, it is always a SAFER bet that the circuit with fewer connections will be more reliable! Connectors, switches, and cables are the most likely failure points in electronics.*
I hate those damned adapters. I've been screwed twice when my kids loaned me SDXC Micro cards in an adapter. They corrupted one job and outright failed to mount properly on another. NEVER AGAIN.
I do not scrimp on cards. If a device CALLS for a Micro SD card, I'll use one, but I'll use the Micro SD slot on my high speed card reader, rather than put the card in an adapter to read it. I simply won't use a Micro SD in an SD adapter.
*Static electricity and AC power surges (spikes) come second. Bad connections are often responsible for those AC power line spikes! THINK: "back-wired" AC receptacles on outside walls of homes built in the last 40 years or so… Moisture from condensation causes corrosion to start. That builds up a resistant film that leads to arcing, pitting, and those power spikes that damage electronics. The gripping fingers in the backs of those cheap outlets fail due to metal fatigue and relax their grips on the wires. I've replaced dozens of them over the years, always using the screw terminals of higher quality receptacles when I do.
burkphoto wrote:
I wired a radio station in my early 20s. The chief engineer taught me a very valuable lesson: When confronted with a choice of more or fewer connections in any circuit, it is always a SAFER bet that the circuit with fewer connections will be more reliable! Connectors, switches, and cables are the most likely failure points in electronics. Static electricity and AC power surges (spikes) come second.
I hate those damned adapters. I've been screwed twice when my kids loaned me SDXC Micro cards in an adapter. They corrupted one job and outright failed to mount properly on another. NEVER AGAIN.
I do not scrimp on cards. If a device CALLS for a Micro SD card, I'll use one, but I'll use the Micro SD slot on my high speed card reader, rather than put the card in an adapter to read it. I simply won't use a Micro SD in an SD adapter.
I wired a radio station in my early 20s. The chief... (
show quote)
Bummer. I've not had a problem with any micros in adapters in the years I've been using them.
I have no qualms about micros in adapters.
burkphoto wrote:
I wired a radio station in my early 20s. The chief engineer taught me a very valuable lesson: When confronted with a choice of more or fewer connections in any circuit, it is always a SAFER bet that the circuit with fewer connections will be more reliable! Connectors, switches, and cables are the most likely failure points in electronics.*
I hate those damned adapters. I've been screwed twice when my kids loaned me SDXC Micro cards in an adapter. They corrupted one job and outright failed to mount properly on another. NEVER AGAIN.
I do not scrimp on cards. If a device CALLS for a Micro SD card, I'll use one, but I'll use the Micro SD slot on my high speed card reader, rather than put the card in an adapter to read it. I simply won't use a Micro SD in an SD adapter.
*Static electricity and AC power surges (spikes) come second. Bad connections are often responsible for those AC power line spikes! THINK: "back-wired" AC receptacles on outside walls of homes built in the last 40 years or so… Moisture from condensation causes corrosion to start. That builds up a resistant film that leads to arcing, pitting, and those power spikes that damage electronics. The gripping fingers in the backs of those cheap outlets fail due to metal fatigue and relax their grips on the wires. I've replaced dozens of them over the years, always using the screw terminals of higher quality receptacles when I do.
I wired a radio station in my early 20s. The chief... (
show quote)
My SAFER BET does incude an extra set of contacts (as explained at the outset).
If you want to reply, then
register here. Registration is free and your account is created instantly, so you can post right away.