Somewhat unrelated to the OP’s first post with concerns about sensor cleaning but pertinent otherwise.
Amazon seems to want to sell everytging under the sun but they are not always accurate and thorough in ther product descriptions. I could not find locally a new tractor ignition switch so ordered one from Amazon. When it arrived it was for a different model and didn’t fit. There was one digit in the fitment description of the tractor model number that was off. I returned it.
So I removed the broken one intending to take it to the dealer to ensure they ordered an exact replacement. When doing so I found one lead that was bad, repaired it and voilà shefired right up. So a ten cent repair at most.
As to sensor cleaning I have rarely needed to clean a sensor. Only once actually. More often I have found the fault to be dust or whatever on a prism or mirror. The one time I did I used a kit made by Photosol PSI, followed its directions, and got the job done without problems or difficulties.
charles tabb wrote:
Whenever I think that I have a sensor dot, to be sure I wait until there is a nice blue sky and shoot up at that. This will show even the smallest dot on my sensor. Then I remove the lens from my camera. I then get out my "Sensor KLEAR Loupe. This device has a cylinder that goes over the opening that has a ring of high intensive led bulbs that brightly light up the sensor with a strong magnifier lens . The side of tube has an opening which allows me to insert a cleaning wand down through and clean all that is necessary. I also have some wet cleaning wipe sticks, however haven't had to use the first one as yet. (Hope this helps).
Whenever I think that I have a sensor dot, to be s... (
show quote)
Do you remember from whom you bought the Sensor Klear Loupe?
Personally, I like the plain ole squeeze bulb.
Bout as high tech as I can handle.
plumbbob1 wrote:
Personally, I like the plain ole squeeze bulb.
Bout as high tech as I can handle.
Same here except for the one and only time I did have an irritating blob of what not on the glass cover of the sensor I couldn’t get rid of with the bulb gadget.
I read somewhere that you should only use 99% isopropyl alcohol to clean lenses not camera sensors and Ecplise E2 is still the best fluid to use. But I'm open to anyone with more knowledge.
I had a bad problem on my mirrorless Canon M50. I couldn’t get it off. Finally took it to camera shop and got it off. Recently I noticed another spot on camera. I tried a blower which didn’t get it. I used a sensor brush and that did the trick. I checked my
DSLR and it is still spotless.
jerryc41 wrote:
I've always heard that you shouldn't use a vacuum to clean the inside of a camera and a computer, but I don't know the reasoning behind that advice. Maybe that only applies to very powerful vacuums.
Maybe static electricity generation?
I use sensor wipes...never had a problem or thought it was complicated.
Dust can be blown out...but sometimes...it won't.
iamimdoc wrote:
Decided to try the Carson 4.5X 30 mm Camera Sensor Magnifier
1 On the box is "*Not compatable (sic) with mirrorless cameras". Did not see this in Amazon ad. My bad.
As I intended to use on a Nikon D200 and D300 and Sony 6400, I seem to be out of luck.
Yes/no/comments/solutions? There is a larger 40 mm device. Is this more usable to me or just for larger sensors?
2 Are these devices even necessary? On one YouTube video, the presenter just turned on his cell phone light and used it to highlight the sensor.
3 Looking at more videos, it appears these devices have trouble at times with various mounts. Not clear but maybe some mounts, due to size, prevented accurate focusing on the sensor. Is this an issue?
Thanks for advice.
Decided to try the Carson 4.5X 30 mm Camera Sensor... (
show quote)
I never use one. I do the blue sky test at a small aperture.
I have struggled with sensor cleaning. The major thing I've learned is to be careful and not expose the camera. For example, I live in a dusty environment. When I go certain places, I just never change a lens. Plan ahead and make the best choice with the fewest compromise. When I am home I clean with one of those rocked looking squeeze balls. Also before changing a lens, I turn off the camera and wait 5 seconds. The gives static electricity a chance to die out. I also get everything ready so the camera isn't open very long.
I did a very stupid thing when I was in Antarctica in Dec 2022. I had a spot on my Z9 in the lower right
hand corner of the pictures. It was large so I figured I could remove it by blowing on it. Terrible idea. as Forest Gump's mom said, stupid is as stupid does. I managed to
get liquid on my sensor in many places. Things are bumpy on cruise boat in the Antarctic. So instead of one spot I had about 25 spots, making for enormous Photoshop time. When I got home I packed the camera up and shipped it to Nikon. I was prepared for a big bill - sensor replacement. Instead I got a response that they would clean it under the warranty - the camera was 11 months. So under a week I got it back, clean as a whistle, and everything else re-calibrated. I popped a bottle of Champaign and congratulated myself
stenstromk wrote:
...I did a very stupid thing when I was in Antarctica in Dec 2022. I had a spot on my Z9 in the lower right
hand corner of the pictures. It was large so I figured I could remove it by blowing on it. Terrible idea...
When I first started with photography back in the early 70's I read that you should never try to blow dust off a lens as it is very hard to blow and not spit. I guess you found out the hard way.
flip1948 wrote:
When I first started with photography back in the early 70's I read that you should never try to blow dust off a lens as it is very hard to blow and not spit. I guess you found out the hard way.
That’s why you use a rocket blower and not your breath.
agillot wrote:
I dont understand why people are looking for high tech way to remove dust particle from the sensor , when a mini shop vac $ 30 , does that to perfection . I guess too easy .
He’s not talking about a device to clean the sensor. It’s a lighted magnifier to view the sensor and can be useful to see things that aren’t coming off by simple blowing. The problem is they usually have a limited focus range and with the mirrorless flange distance being less they won’t focus when sitting on the flange.
I would never use a vacuum of any kind to clean a sensor. I’ve always cleaned my own. First step is a rocket blower with the camera facing down so any loosened dust falls out rather than back into the camera. If it’s still dirty I use cleaner and the correct size sensor swab for that sensor.
SuperflyTNT wrote:
He’s not talking about a device to clean the sensor. It’s a lighted magnifier to view the sensor and can be useful to see things that aren’t coming off by simple blowing. The problem is they usually have a limited focus range and with the mirrorless flange distance being less they won’t focus when sitting on the flange.
I would never use a vacuum of any kind to clean a sensor. I’ve always cleaned my own. First step is a rocket blower with the camera facing down so any loosened dust falls out rather than back into the camera. If it’s still dirty I use cleaner and the correct size sensor swab for that sensor.
He’s not talking about a device to clean the senso... (
show quote)
Evidently some use the rocket or vac...and if that doesn't work...they send it out to be cleaned.
I do the same as you...right size...takes a minute...literally...done.
Canisdirus wrote:
Evidently some use the rocket or vac...and if that doesn't work...they send it out to be cleaned.
I do the same as you...right size...takes a minute...literally...done.
Yes, and one pass with one side of swab, return pass with the other side and throw the swab away. If it needs another pass use a fresh swab.
If you want to reply, then
register here. Registration is free and your account is created instantly, so you can post right away.