Problem Attaching Camera to Tripod
Mar 28, 2023 18:24:51 #
chrissybabe
Loc: New Zealand
If you are happy to use the camera hand hold from here on no problem. If fixing the bottom mounting screw is a must then you have nothing to lose because the alternative is that the camera has just become a paperweight.
Here is a photo showing the mounting frame that I adapted to hold my Panasonic Lumix. The frame was for a different model but mostly fitted. One feature that I couldn't use (the photo) shows where a screw would be used to hold the strap lug onto the bracket. This would provide a huge heap of extra support for the camera (although not needed in my case). An example of the sort of thing to watch out for.
Here is a photo showing the mounting frame that I adapted to hold my Panasonic Lumix. The frame was for a different model but mostly fitted. One feature that I couldn't use (the photo) shows where a screw would be used to hold the strap lug onto the bracket. This would provide a huge heap of extra support for the camera (although not needed in my case). An example of the sort of thing to watch out for.
Mar 28, 2023 18:29:45 #
Or, you can just not use the tripod and shoot at an adequate SS/ISO to prevent visible camera shake.
Mar 28, 2023 19:52:58 #
TriX wrote:
Or, you can just not use the tripod and shoot at an adequate SS/ISO to prevent visible camera shake.
You are no fun
Mar 28, 2023 20:56:25 #
Mar 28, 2023 23:16:24 #
Dr. Joel Germond wrote:
My quess is the threads have worn because that is a heavy camera (have one) and very forward leaning when zoomed. I obtained a plate so I could move the body further back, thus moving center of gravity back for balance.I'd been leaving my Nikon P1000 attached to the tripod at all times because it's been the only way I ever use it....It probably got bumped in the car or something, but really, I don't know for sure..
Mar 29, 2023 01:05:37 #
Mar 29, 2023 02:59:28 #
Littledab
Loc: Wyoming
Excellent advice. I have used thread chasers multiple times for thread restoration. Normal taps are fine for use where the male component extends thru the repaired piece.
Mar 29, 2023 03:18:18 #
Dr. Joel Germond wrote:
Has anyone ever had a problem with the threads on the inside of the tripod mount? My Tripod attached just fine to all of my cameras except one so I know it's the camera, not the tripod. I think the threads inside the camera mount may have become stripped. Has anyone ever had something like this repaired?
If you decide to not take/send your camera in for repair, and before attempting to re-tap (I would not go this route myself) I look would into using a "Loctite" product.
Loctite has a whole family of products intended for use in applications involving threads.
Loctite has a product specifically for repairing stripped threads.
I would contact manufacture (Henkel Adhesive Technologies) and seek their guidance.
Tech Support:
1-855-Henkel4
Mar 29, 2023 07:59:47 #
Somebody already mentioned a repair kit. Here's a video showing how to use it.
https://www.youtube.com/watch?v=_gn2mM6vg5U
---
https://www.youtube.com/watch?v=_gn2mM6vg5U
---
Mar 29, 2023 08:24:33 #
Bill_de wrote:
Somebody already mentioned a repair kit. Here's a video showing how to use it.
https://www.youtube.com/watch?v=_gn2mM6vg5U
---
https://www.youtube.com/watch?v=_gn2mM6vg5U
---
Looks like it requires drilling out the old damaged thread and inserting a helicoil repair to restore the original size thread.
My concern is with (1) the drilling on the camera. Producing metal chips. Not something you want getting into your camera. At the very least it would be a two-person job with a good vacuum cleaner right up next to the drilling point and a stable drilling platform (a drill press, not a hand-held drill) to get the hole straight and a way to hold the camera firmly during the drilling. And (2) this would only work if the problem is only a damaged thread, not a threaded component that is no longer firmly attached to the camera body.
Mar 29, 2023 08:38:48 #
DirtFarmer wrote:
Looks like it requires drilling out the old damage... (show quote)
I believe you are making a mountain out of a mole hill. I certainly wouldn't be using a drill press.
Did you actually watch the short video?
---
Mar 29, 2023 09:48:07 #
mikegreenwald
Loc: Illinois
bsprague wrote:
Our cameras use 1/4 inch diameter with twenty threads per inch. (1/4-20). You may be able to ---> carefully <---- clean the threads with a "tap" from any hardware store.
https://www.amazon.com/IRWIN-HANSON-Tap-Drill-80230/dp/B00004YOAS
https://www.amazon.com/IRWIN-HANSON-Tap-Drill-80230/dp/B00004YOAS
Correct, but be sure it's a "bottoming" tap. A conventional tap will not work.
If the threads are so badly stripped that they cannot be restored, a device called a "helicoil" may do the job.
Mar 29, 2023 13:01:34 #
Have you checked if there is any dirt or debris stuck in the threads? That would cause the symptoms you describe.
If you do choose to use a bottoming tap, be slow and gentle with a manual tap wrench or pliers. Never a drill.
Get a good light and a magnifier, you may get lucky......
If you do choose to use a bottoming tap, be slow and gentle with a manual tap wrench or pliers. Never a drill.
Get a good light and a magnifier, you may get lucky......
Mar 29, 2023 13:23:09 #
Lost Again
Loc: Middle of nowhere Oregon
Dr. Joel Germond wrote:
Has anyone ever had a problem with the threads on the inside of the tripod mount? My Tripod attached just fine to all of my cameras except one so I know it's the camera, not the tripod. I think the threads inside the camera mount may have become stripped. Has anyone ever had something like this repaired?
If the threads are too stripped for a tap to help look up helicoil. Helicoil requires a special oversize tap, a 1/4-20 s.s. helicoil and installation tool. We repaired aircraft with them so they work. The kits arn't too expensive and can be purchased thru McMaster Carr. Check the spelling, Helicoil, it's been awhile since I bought a set. It will also take an oversize drill to drill out the old threads before re-tapping for the Helicoil. And yes, you can use them on "blind" holes. Good luck.
Mar 29, 2023 13:50:36 #
clint f.
Loc: Priest Lake Idaho, Spokane Wa
If you are asking it’s likely a repair above your pay grade. Bite the bullet and send it out for repair. If they screw up they are responsible. If you do it and mess up you have no recourse. You can’t sue yourself in a manner of speaking.
If you want to reply, then register here. Registration is free and your account is created instantly, so you can post right away.