Technical issue
Feb 15, 2023 05:37:45 #
gvarner wrote:
Use an air bulb to blow it off. Never used canned air. They contain moisture.
and can spit on the sensor
Feb 15, 2023 06:17:59 #
Reading thru the multi pages the only thing that has not been suggested is "flea and tick collar" !!
Sensors to my amazement are incredibly tough. I converted a Nikon 1 that has a 1" sensor and to my dismay, I need to take it apart and clean the sensor surface. This video will dispel you anxiety about cleaning dust off of you sensor.
https://www.youtube.com/watch?v=xLzrS3aSJWE
Sensors to my amazement are incredibly tough. I converted a Nikon 1 that has a 1" sensor and to my dismay, I need to take it apart and clean the sensor surface. This video will dispel you anxiety about cleaning dust off of you sensor.
https://www.youtube.com/watch?v=xLzrS3aSJWE
Feb 15, 2023 06:25:52 #
ScottWardwell
Loc: Maine
Longshadow wrote:
Curious, where was that explained?
Oh, ...since forever. I think they found a Sumerian tablet with the same warning. And later just missed being included in the "10 Commandments".
Feb 15, 2023 06:32:22 #
Feb 15, 2023 07:03:00 #
Call NORAD. They’ve gotten pretty good at knocking this stuff out of the sky!
Sorry for being a smart ass. Couldn’t help myself! 😂
Sorry for being a smart ass. Couldn’t help myself! 😂
Feb 15, 2023 07:09:49 #
Longshadow wrote:
Curious, where was that explained?
I was wondering the same thing!!
Feb 15, 2023 07:13:45 #
David Martin wrote:
Several sources available online, nearly all basic... (show quote)
The propellant in canned air is a liquid while compressed, and turns to a gas when released, there isn't any moisture/water in it.
Feb 15, 2023 08:24:22 #
Longshadow wrote:
I'll guess a sensor dust particle.
The fact that it's moving indicates it's not stuck on the sensor and it might be able to be blown off with canned air.
Is it there in live view?
The fact that it's moving indicates it's not stuck on the sensor and it might be able to be blown off with canned air.
Is it there in live view?
Feb 15, 2023 08:41:14 #
David Martin
Loc: Cary, NC
Manglesphoto wrote:
The propellant in canned air is a liquid while compressed, and turns to a gas when released, there isn't any moisture/water in it.
Agree. However, as the article I quoted explained, the gas can briefly liquify and stain the mirror or sensor.
Feb 15, 2023 08:47:02 #
David Martin wrote:
Agree. However, as the article I quoted explained, the gas can briefly liquify and stain the mirror or sensor.
Definitely.
That's why one has to know how to properly use it.
Feb 15, 2023 08:47:49 #
Longshadow wrote:
I'll guess a sensor dust particle.
The fact that it's moving indicates it's not stuck on the sensor and it might be able to be blown off with canned air.
Is it there in live view?
The fact that it's moving indicates it's not stuck on the sensor and it might be able to be blown off with canned air.
Is it there in live view?
Don’t use canned air; use a squeeze blow or an arctic butterfly instead.
Feb 15, 2023 08:49:50 #
fetzler
Loc: North West PA
Longshadow wrote:
I'll guess a sensor dust particle.
The fact that it's moving indicates it's not stuck on the sensor and it might be able to be blown off with canned air.
Is it there in live view?
The fact that it's moving indicates it's not stuck on the sensor and it might be able to be blown off with canned air.
Is it there in live view?
DO NOT blow dust off a sensor with canned air you can leave a residue on the sensor.
Instead use a rubber bulb. I have one that has an air filter to remove any small particles. You could also us a Nitecore Blower Baby with the filter for sensor cleaning. In either case turn camera so that the sensor faces down and blow out the sensor area.
Does your Nikon have a sensor cleaning mode? My D7200 has one. it vibrates the sensor when turning on or off (perhaps it is only off or on) the camera. Turn on this mode if possible.
If these fail them you will need a sensor cleaning kit. Also be sure to check your lens surfaces (back, front, and filter)
Feb 15, 2023 08:51:18 #
fetzler
Loc: North West PA
gvarner wrote:
Use an air bulb to blow it off. Never used canned air. They contain moisture.
Not so much moisture but other nasty stuff.
Feb 15, 2023 09:52:20 #
JimBunk wrote:
Couldn’t find the tech discussion group…
I have an issue with my Z50.
It has a artifact in all of my pics.
It has moved around over the last few days.
It doesn’t show when composing the pic, but shows in every pic.
I swapped lenses but it’s still there.
Thinking I need to take it in to Nikon.
Any other suggestions?
I have an issue with my Z50.
It has a artifact in all of my pics.
It has moved around over the last few days.
It doesn’t show when composing the pic, but shows in every pic.
I swapped lenses but it’s still there.
Thinking I need to take it in to Nikon.
Any other suggestions?
There are appropriate tools to remove that.
My recommendation is that if you are squeamish about precise, gentle application of proper tools, send it to Nikon for a CLA (clean, lube, adjust).
If, however, you're handy with tools and can follow instructions explicitly, read these links, especially the first one!
http://cleaningdigitalcameras.com
https://photosol.com (I use their solutions.)
AVOID using CANNED AIR on sensors, mirrors, or ground glass viewing screens unless you first duct tape the half-empty can to a table. It contains liquid propellant that can FREEZE AND CRACK glass. Taping the can to a table avoids spewing freezing death onto your sensor.
Better yet, use a Rocket Air Blaster blower bulb (by Giottos; several others make similar blower bulbs). I always START with the Rocket Blaster. For stuck-on stuff, I use Eclipse fluid and Sensor Swabs.
Feb 15, 2023 09:59:55 #
If you want to reply, then register here. Registration is free and your account is created instantly, so you can post right away.