DirtFarmer
Loc: Escaped from the NYC area, back to MA
DoriguzziPA wrote:
Get an engineer to draw up detailed plans for this!
Parts > $3.00
Tools req's > 947.35 (+ tax)
You don't need a table saw and a drill press for a project like this. Harbor Freight has a lot of pretty good hand tools that will suffice. I have a hand saw that probably cost less than $10. A C clamp to hold the wood down. Probably the most expensive tool would be a drill. Most people who build things occasionally probably have a drill already. If you don't you can buy a couple drill bits and a pair of pliers and maybe a round file.
The limitation is on your manual dexterity and your ability to do things carefully.
Fortunately for me, I already have a drill press and a table saw.
Another good way is to use an iphone or equivalent with a program like softbox. Take the slide, put it on the phone with the program loaded and put the camera on a tripod or a stable surface and take a close up photo. Mine worked pretty good.This is a 50+ year old slide. I took it on macro mode with my sony dsc rx10m3. It might look a little grainy but I think it looks pretty good. You put the program on white color and bright and it looks ok. (I think!) Put it onto your device and edit it. I used my IPad with photos after importing it from the Sony transfer (wireless) program. It is easy.
DirtFarmer wrote:
You don't need a table saw and a drill press for a project like this. Harbor Freight has a lot of pretty good hand tools that will suffice. I have a hand saw that probably cost less than $10. A C clamp to hold the wood down. Probably the most expensive tool would be a drill. Most people who build things occasionally probably have a drill already. If you don't you can buy a couple drill bits and a pair of pliers and maybe a round file.
The limitation is on your manual dexterity and your ability to do things carefully.
Fortunately for me, I already have a drill press and a table saw.
You don't need a table saw and a drill press for a... (
show quote)
I have a chop saw, but prior to that, I had a simple wooden mitre box that came with a small mitre saw that was very inexpensive. I made many picture frames and moldings with it. Just a coping saw, a block of wood, and some sandpaper would suffice. If you don't have a drill and 9/16 bit, borrow one.
I always like a project like this so I can buy new tools and my wife believes I'm saving money!
Regardless of the cost, I will always prefer a dedicated film/slide scanner and the reason is very simple: the IR dust and scratch cleaning capabilities.
Amielee
Loc: Eastern Washington State
I used an old slide sorter from film days that I had. Put a 6000 K. LED bulb behind it and photographed the slides with a Canon SX 60. They came out excellent. Slides were of the kids when they were children. Made copies for each of them.
Streets. Please don't think I'm being picky about your post, you just hit on one of my favorite peeves. In fact I'm quite impressed by your solution to your slide copying problem.
"a 1/4 x 20 screw, or bolt"
What's the difference between a screw and a bolt? A bolt has a nut and a screw does not.
My most favorite peeve?; authors who write about cutting pipe threads. "get an NPT pipe tap (National Pipe Thread). Nope, sorry, NPT is short for National Pipe Tapered. And yes there is an NPS (National Pipe Straight) If you own a paint spray gun the fitting at the bottom of the handle is an NPS thread.
It snowed last night, it's cold as the Arctic outside, the new AF lens hasn't arrived yet and I'm bored.
Rick
Fotoartist wrote:
I don't know that it works perfectly unless your original slide was that blue to begin with.
But then that can be easily fixed in a couple of steps.
DoriguzziPA wrote:
Get an engineer to draw up detailed plans for this!
Parts > $3.00
Tools req's > 947.35 (+ tax)
I’m up for any excuse to buy tools.
DirtFarmer
Loc: Escaped from the NYC area, back to MA
farwest wrote:
I always like a project like this so I can buy new tools and my wife believes I'm saving money!
"Any decent project is a valid excuse for a new tool."
Don, the 2nd son wrote:
I explored a few variants like this but the light source problem can be daunting.
An iPhone 7 Plus or iPhone 8 Plus and a custom white balance works great. Keep the phone plugged into a power adapter and set it at maximum brightness and never to sleep.
Be sure to mask ALL stray light from entering your lens.
Use raw capture and post-processing for best results. You can recover highlight and shadow details that a JPEG would never contain.
Kozan
Loc: Trenton Tennessee
Fotoartist wrote:
I don't know that it works perfectly unless your original slide was that blue to begin with.
Skin tones look natural and the "whites" look white. I think the OP did a great job.
For a light source I'd suggest a 60 - 70 watt equivalent LED bulb. I made a homemade slide/negative copier box and picked up a couple LED bulbs from the local big box home improvement store. Advantage to the LED bulbs is that you can pick your color temperature. I got 5,000 K, which is getting close to daylight.
SteveFranz wrote:
For a light source I'd suggest a 60 - 70 watt equivalent LED bulb. I made a homemade slide/negative copier box and picked up a couple LED bulbs from the local big box home improvement store. Advantage to the LED bulbs is that you can pick your color temperature. I got 5,000 K, which is getting close to daylight.
Full spectrum LEDs are EXPENSIVE.
Here’s a great resource:
https://forums.negativelabpro.com/t/suggested-backlight-sources-for-scanning-film-with-dslr/130/01(74 pages of discussion about color-accurate light sources)
Kozan wrote:
Skin tones look natural and the "whites" look white. I think the OP did a great job.
Thanks Kozan. I like my monitor screen light source, and a white sheet of paper in sunlight also works well as a backdrop. I also am happy using auto white balance mode on my sony.
If you want to reply, then
register here. Registration is free and your account is created instantly, so you can post right away.