I recently got a Nikon Speedfalsh SB25. I will use it on the Nikkormat FT2. I don't think the FT2 supports the TTL mode. I have the manual for the flash and although it does have a lot of options, I am not sure how to set it for fill flash. I don't want to waste a roll of film if I don't set it right. I have been using the Manual Mode. Is this the best option or can I us it in Auto Mode? Any help would be greatly appreciated.
I recently got a Nikon Speedfalsh SB25. I will use it on the Nikkormat FT2. I don't think the FT2 supports the TTL mode. I have the manual for the flash and although it does have a lot of options, I am not sure how to set it for fill flash. I don't want to waste a roll of film if I don't set it right. I have been using the Manual Mode. Is this the best option or can I us it in Auto Mode? Any help would be greatly appreciated.
You are right, the FT2 does not support TTL. For fill flash in auto mode, on the flash set either the f/stop wider than your working aperture, or the ISO higher than your film speed. Good to see another film shooter!
If you go about some simple testing along with note taking, you won't waste a roll of film. You'll have established a known set of results with a known set of parameters. --Bob
SpyderJan wrote:
I recently got a Nikon Speedfalsh SB25. I will use it on the Nikkormat FT2. I don't think the FT2 supports the TTL mode. I have the manual for the flash and although it does have a lot of options, I am not sure how to set it for fill flash. I don't want to waste a roll of film if I don't set it right. I have been using the Manual Mode. Is this the best option or can I us it in Auto Mode? Any help would be greatly appreciated.
You are right, the FT2 does not support TTL. For fill flash in auto mode, on the flash set either the f/stop wider than your working aperture, or the ISO higher than your film speed. Good to see another film shooter!
You are right, the FT2 does not support TTL. For fill flash in auto mode, on the flash set either the f/stop wider than your working aperture, or the ISO higher than your film speed. Good to see another film shooter!
Thanks for the input. Should I start with one stop or two. I seem to remember seeing something about this before, but I will take your advice.
If you go about some simple testing along with note taking, you won't waste a roll of film. You'll have established a known set of results with a known set of parameters. --Bob
You are right, the FT2 does not support TTL. For fill flash in auto mode, on the flash set either the f/stop wider than your working aperture, or the ISO higher than your film speed. Good to see another film shooter!
I will try a new roll of film and test. As far as a film shooter. I have been at it on and off for over 50 years.
Depends pretty much on the scene and just how much fill it needs. I would bracket 1, 1-1/2 and 2 stops at first. After awhile you’ll know without thinking much about it. I don’t keep track of settings unless for a test, but probably most of my fill is -1 stop.
Depends pretty much on the scene and just how much fill it needs. I would bracket 1, 1-1/2 and 2 stops at first. After awhile you’ll know without thinking much about it. I don’t keep track of settings unless for a test, but probably most of my fill is -1 stop.
Thank you for your response. I put a fresh roll in the Nikkormat, and I will be trying out the fill settings today. Have a respectful Memorial Day.
I recently got a Nikon Speedfalsh SB25. I will use it on the Nikkormat FT2. I don't think the FT2 supports the TTL mode. I have the manual for the flash and although it does have a lot of options, I am not sure how to set it for fill flash. I don't want to waste a roll of film if I don't set it right. I have been using the Manual Mode. Is this the best option or can I us it in Auto Mode? Any help would be greatly appreciated.
As the other posters have said, a little experiment with note taking is good.
A good starting point is the guide number.
The SB25 has a GN of 118. (meters) so it's 138 feet at the 35mm setting at ASA 100. (and always quoted at 1/1.)
So I'd start there. I'd start with a fill of 50% of the recommended power and distance above.
Use the guide number calculator and keep notes on what works, then write it down and tape it to the side of your flash.